A modul (Micro SD Card Adapter) egy Micro SD kártyaolvasó modul. A modul az Arduino-val való kommunikációjához SPI buszt használ.
A modul csatlakoztatását követően a modulba behelyezett kártya fájlrendszere az Arduino felől elérhető, az írható és/vagy olvasható.
Jellemző felhasználása: mérésadatok loggolása.
Az Arduino SPI összefoglalása itt található: Arduino SPI.
Az Aduino-s SPI megoldások összefoglalása itt található: Arduino SPI kommunikáció.
A modulban felhasználásra szánt SD kártyát előzetesen formattálni kell. Az Arduino megbirkózik a FAT16 és FAT32-es formátumokkal is, mindenesetre a FAT16 a támogatott. Az SD kártyán használt fájlnevek esetében a szigorúbb, 8.3 forma érvényes, azaz 8 karakter fájlnév és 3 karakter kiterjesztés. Fontos, hogy a file.write() parancs mindaddig nem ír az SD kártyára, míg az előző írásműveletet vagy a close() vagy a flush() paranccsal le nem zárjuk azt. A legegyszerűbb rögtön az írás után lezárni a nyitott fájlt:
File dataFile = SD.open(filename, FILE_WRITE);
if (dataFile) {
dataFile.println(dataString);
dataFile.close();
// print to the serial port too:
Serial.println(dataString);
}
Több típusú kártyamodul is létezik a piacon, itt most csak ezt az egyet ismertetem. Ha szükséges, kibővítem a dokumentációt.
A kártyamodul portjait az alábbiak szerint érdemes az Aduino UNO-val vagy Mega-val összekötni:
Micro SD | Arduino Uno | Arduino Mega |
CS | pin 4 | pin 53 |
SCK | pin 13 | pin 52 |
MOSI | pin 11 | pin 51 |
MISO | pin 12 | pin 50 |
VCC | 5V | 5V |
GND | GND | GND |
A Micro SD kártyamodul leírása a Arduino oldalon itt található:
https://www.arduino.cc/en/Reference/SD
A Micro SD kártyamodul könyvtára innen tölthető le: https://github.com/greiman/SdFat
Ugyaninnen a példaprogramok széles választéka is letölthető: https://github.com/greiman/SdFat/tree/master/examples
SD card datalogger szoftver megjelenítése
SD card datalogger szoftver megjelenítése
/*
SD card datalogger
This example shows how to log data from three analog sensors
to an SD card using the SD library.
The circuit:
analog sensors on analog ins 0, 1, and 2
SD card attached to SPI bus as follows:
** MOSI - pin 11
** MISO - pin 12
** CLK - pin 13
** CS - pin 4 (for MKRZero SD: SDCARD_SS_PIN)
created 24 Nov 2010
modified 9 Apr 2012
by Tom Igoe
This example code is in the public domain.
*/
#include <SPI.h>
#include <SD.h>
const int chipSelect = 4;
void setup() {
// Open serial communications and wait for port to open:
Serial.begin(9600);
while (!Serial) {
; // wait for serial port to connect. Needed for native USB port only
}
Serial.print("Initializing SD card...");
// see if the card is present and can be initialized:
if (!SD.begin(chipSelect)) {
Serial.println("Card failed, or not present");
// don't do anything more:
while (1);
}
Serial.println("card initialized.");
}
void loop() {
// make a string for assembling the data to log:
String dataString = "";
// read three sensors and append to the string:
for (int analogPin = 0; analogPin < 3; analogPin++) {
int sensor = analogRead(analogPin);
dataString += String(sensor);
if (analogPin < 2) {
dataString += ",";
}
}
// open the file. note that only one file can be open at a time,
// so you have to close this one before opening another.
File dataFile = SD.open("datalog.txt", FILE_WRITE);
// if the file is available, write to it:
if (dataFile) {
dataFile.println(dataString);
dataFile.close();
// print to the serial port too:
Serial.println(dataString);
}
// if the file isn't open, pop up an error:
else {
Serial.println("error opening datalog.txt");
}
}